HAGAR [Discontinued]

SBC with NXP i.MX 6SoloX Processor

Available in Industrial Temperature Range

Data sheet

Cpu

NXP i.MX 6SoloX Processor, Single core Cortex®-A9 @ 1GHz + Cortex®-M4 core @ 227MHz

Graphics

Integrated Graphics Vivante GC400T, 2D and 3D HW accelerator

Connectivity

up to 2x Fast Eth; optional WiFi + BT LE

Memory

32-bit DDR3L memory soldered on-board, up to 1GB

Product details

Technical Info

Description	HAGAR is a new-generation all-in-one low-cost SBC designed by SECO, equipped with a NXP i.MX 6SoloX applications processor able to run Linux. HAGAR is a revolutionary product in terms of connectivity, interactivity with the real world and cost: a new concept of single board computer ready for Internet of Things applications and for the Post-PC era.
Cpu	NXP i.MX6SX SoloX Processor, Single core Cortex®-A9 @ 1GHz + Cortex®-M4 core @ 227MHz
Max Cores	1 + 1
Memory	Soldered on-board DDR3L memory, 32-bit interface, up to 1GB
Graphics	Integrated Graphics Vivante GC400T, 2D and 3D HW accelerator OpenGL ES 2.0, OpenGL ES 1.1, OpenVG 1.1 supported
Video Interfaces	Single Channel 18-/24- bit LVDS connector + Touch Screen (I2C signals) 24-bit Parallel RGB Connector
Video Resolution	LVDS: up to 1366x768 @60Hz, 24bpp RGB: up to 1920x1080p @60Hz, 24bpp
Mass Storage	16MB NOR Quad-SPI Flash soldered onboard µSD Card slot Optional eMMC drive soldered on-board, up to 8GB
Networking	Up to 2x Fast Ethernet RJ-45 connectors Optional WiFi (802.11 b/g/n) + BT LE combo module + antenna onboard
Usb	1 x USB 2.0 OTG port 3 x USB 2.0 Host ports on standard Type-A socket 1 x USB 2.0 Host port on internal pin header
Audio	I2S Audio interface on programmable pin header S / PDIF interface (In and Out) on programmable pin header
Serial Ports	1 x CAN Port reconfigurable as GPIO 2x RS-232 (Tx/RX signals only) + 1x RS-485 serial ports on expansion pin header
Other Interfaces	2 x I2C dedicated connectors (one reserved for Touch Screen) 6 analog inputs for A/D Conversion Programmable () expansion pin header connector, able to offer: • CSI interface input (PAL and NTSC formats supported) • Up to 20 GPIO • SPI interface • SPDIF Audio interface • I2S Audio interface • CAN interface (TTL level) • 5 x PWM • 3 x I2C • 3 x serial ports (2x RS-232 +1xRS-485 interface) Embedded Low Power RTC () Please note that some of these interfaces are factory options, other configurations are made via SW using the pin multiplexing possibilities of the i.MX6SX processor. Optional 9-Axis Motion Sensors (Accelerometer, Magnetometer and Digital Gyroscope)
Power Supply	+12VDC nominal voltage +3VDC cabled Coin Cell Battery
Operating System	Linux Yocto
Operating Temperature	0°C ÷ +60 °C (commercial temp.)* -40°C ÷ +85°C (industrial version) *Measured at any point of SECO standard heastpreader for this product, during any and all times (including start-up). Actual temperature will widely depend on application, enclosure and/or environment. Upon customer to consider application-specific cooling solutions for the final system to keep the heatspreader temperature in the range indicated.
Dimensions	89.5 x 87 mm (3.52” x 3.43”)